Oceanic 373 Catamaran - 'Fastbuild Kit'

Round bilge hulls finished up to water line.
Decks and outer hull sides port & starboard; Deck incorporating moulded non skid, stern steps, swim ladders recessed mounting points, engine hatches, cockpit seating, hatch mounting areas, stanchions and cleat mounting points. Outer hull moulded down to water line height.
Inner hull sides with chamfer panels port & starboard.
Forward web with anchor lockers and bridge deck stiffeners with moulded non skid.
Bridge deck with stiffeners.
Saloon roof with extension over the cockpit area, moulded hatch area points (2 medium, 2 small), headsail tracks, turning block pads, winch pads, anchor winch mounting point, and moulded non skid.
Cockpit stern seat incorporating mainsheet track and winch pad positions.
Catwalk with non skid.
Centre cases in halves.
Dagger boards in halves.
Rudders in halves.
Bow noses.
Anchor lockers hatches covers.
Anchor winch hatch cover.
Anchor chain/rope hatch cover.
Cockpit seats lids/hatch covers.
Engine room cover hatches with non skid.
Swim ladder cover lids.
Steering station plinth.
Steering station base.
Instruments and engines control panel.

Flat Panel Pack

Bulkheads CNC cut with jigsaw puzzled joining points.
Floors soles and under floor sole structure, marked ready for cutting out.

Other

Filament wound rudder trunk tubes.
Bulkhead positions marked in the hulls at our workshop for accuracy and time saving.
Aluminium forebeam complete, fully manufactured.
Building assembly jig.

Material to assemble and bond the kit

Resin and catalyst.
Tapes for bonding and reinforcing components.
Powders for filling, fairing and gluing
Timber for compression post.

Assembly Instruction and Engineering Drawings

Assembly manual.
Set of drawings for sail plan,engineering items, plumbing, electrical and other.
Material Safety Data Sheets.

COMPLETE FACTORY BACK UP WITH THE PROJECT

Construction and materials.

Construction of the kit utilises infusion method and modern composite moulding techniques. Hull and deck structures are built utilising modified epoxy resins, core materials are a combination of PVC foam and end grain balsa, with multiaxial glass cloths as reinforcement. All parts that require bonding via glass tapes is performed in rebated grooves of the moulded parts, requiring very minimal fairing and colour blending at the end of the job.

STAGE 2

All of Stage 1 plus

Furniture Components

Saloon settee.
TV/Bar/Book cabinet.
Galley unit with combined overhead cabinet, side fridge cabinet, bench and under bench storage cabinet, inboard side starboard.
Sink and storage bench cabinet outboard side starboard.
Navigation table inboard side mid hull port.
Mid hull storage bench cabinet outboard side port.
Over head lockers for forward, mid and aft areas, 6 in total.
Forward cabins port and starboard, inboard side cabinets, 4 in total.
Forward cabins port and starboard, outboard side cabinet.
Head and shower floor with moulded non skid and toilet plinth.
Vanity cabinet for head/shower area.
Side cabinet outboard side for head and shower area.

Proudly Designed and built in Victoria, Australia

000R M K0 M a r i n e0000000000000000000000 00 00 00 00 00 000000 0000000Fastbuild Kit 0 Factory Built0 Components 0 Gallery 0 About Us 0 Site Map 0 Contact Us

Everything in one kit The Oceanic 373 Fastbuild kit (FBK) is infusion moulded, achieving the ultimate strength to weight ratio for composite construction. With the added advantage of fully finished gelcoat surfaces with moulded nonskid deck patterns. INCLUDED IN THE KIT - Stage 1 Round bilge hulls finished up to water line. Decks and outer hull sides port & starboard; Deck incorporating moulded non skid, stern steps, swim ladders recessed mounting points, engine hatches, cockpit seating, hatch mounting areas, stanchions and cleat mounting points. Outer hull moulded down to water line height. Inner hull sides with chamfer panels port & starboard. Forward web with anchor lockers and bridge deck stiffeners with moulded non skid. Bridge deck with stiffeners. Saloon roof with extension over the cockpit area, moulded hatch area points (2 medium, 2 small), headsail tracks, turning block pads, winch pads, anchor winch mounting point, and moulded non skid. Cockpit stern seat incorporating mainsheet track and winch pad positions. Catwalk with non skid. Centre cases in halves. Dagger boards in halves. Rudders in halves. Bow noses. Anchor lockers hatches covers. Anchor winch hatch cover. Anchor chain/rope hatch cover. Cockpit seats lids/hatch covers. Engine room cover hatches with non skid. Swim ladder cover lids. Steering station plinth. Steering station base. Instruments and engines control panel. Flat Panel Pack Bulkheads CNC cut with jigsaw puzzled joining points. Floors soles and under floor sole structure, marked ready for cutting out. Other Filament wound rudder trunk tubes. Bulkhead positions marked in the hulls at our workshop for accuracy and time saving. Aluminium forebeam complete, fully manufactured. Building assembly jig. Material to assemble and bond the kit Resin and catalyst. Tapes for bonding and reinforcing components. Powders for filling, fairing and gluing Timber for compression post. Assembly Instruction and Engineering Drawings Assembly manual. Set of drawings for sail plan,engineering items, plumbing, electrical and other. Material Safety Data Sheets. COMPLETE FACTORY BACK UP WITH THE PROJECT Construction and materials. Construction of the kit utilises infusion method and modern composite moulding techniques. Hull and deck structures are built utilising modified epoxy resins, core materials are a combination of PVC foam and end grain balsa, with multiaxial glass cloths as reinforcement. All parts that require bonding via glass tapes is performed in rebated grooves of the moulded parts, requiring very minimal fairing and colour blending at the end of the job. STAGE 2 All of Stage 1 plus Furniture Components Saloon settee. TV/Bar/Book cabinet. Galley unit with combined overhead cabinet, side fridge cabinet, bench and under bench storage cabinet, inboard side starboard. Sink and storage bench cabinet outboard side starboard. Navigation table inboard side mid hull port. Mid hull storage bench cabinet outboard side port. Over head lockers for forward, mid and aft areas, 6 in total. Forward cabins port and starboard, inboard side cabinets, 4 in total. Forward cabins port and starboard, outboard side cabinet. Head and shower floor with moulded non skid and toilet plinth. Vanity cabinet for head/shower area. Side cabinet outboard side for head and shower area. Proudly Designed and built in Victoria, Australia	Just look at the finish! Your own catamaran will have the same beautiful finish as every other Oceanic 373 Essentially, you simply assemble the bulkhead structure (upright) then fit the finished outer shell around it.

		Putting it all together couldn't be easier Click on the images for the 9 simple stages to your completed Oceanic 373 Kit
	Oceanic 373 Specifications Click here Contact Us for all the details
DISCLAIMER (A) We reserve the right to make changes and modifications without notice (B) Specifications stated are provisional and based on designed parameters and not actual vessel. © copyright RMK Marine 2009 - 2014